Search Results

This paper describes the development and implementation of an accurate and repeatable path-following algorithm focused ultimately on vehicle testing. A compact, lightweight, and portable hardware package allows easy installation and negligible impact on the vehicle mass, even for the smallest automobile. Innovative features include the ability to generate a smooth, evenly-spaced path vector regardless the quality of the given path. The algorithm proposed in this work is suitable for testing in a controlled environment. The system was evaluated in simulation and performed well in road tests at low speeds.

This paper covers research conducted at the National Highway Traffic Safety Administration's Vehicle Research and Test Center (VRTC) examining the performance of semitrailer anti-lock braking systems (ABS). For this study, a vehicle dynamics model was constructed for the combination of a 4×2 tractor and a 48-foot trailer, using TruckSim. ABS models for the tractor and trailer, as well as brake dynamics and surface friction models, were created in Simulink so that the effect of varying ABS controller parameters and configurations on semitrailer braking performance could be studied under extreme braking maneuvers. The longitudinal and lateral performances of this tractor-trailer model were examined for a variety of different trailer ABS controller models, including the 2s1m, 4s2m, and 4s4m configurations. Also, alternative controllers of the same configuration were studied by varying the parameters of the 2s1m controller.

In this research, cervical muscle behavior in rear impact accidents was investigated. Specifically, cervical muscle forces and muscle lengthening velocities were investigated with respect to cervical injuries. Variation of the onset time for muscle activation, variation of muscle activation level and variation of rear impact pulses were considered. The human body simulation computer program, MADYMO and anthropometric numerical human model were used to evaluate the neck. The factors mentioned above were examined with specific data being obtained from several different literature sources. Cervical muscles were separated into three groups, the sternocleidomastoideus, the flexor muscle group and the extensor muscle group. Longuscolli and spleniuscapitis were selected to represent the flexor muscle and extensor muscle groups respectively. The values and trends of the muscle forces and lengthening velocities are investigated in each muscle group.

Interest in pedestrian head injury has prompted a need to measure the potential of head injury resulting from vehicular impacts. A variety of head impactors have been developed to fulfill this measurement need. A protocol has been developed by the International Harmonization Research Activity (IHRA) to use head impactor measurements to predict head injury. However, the effect of certain characteristics of the various head impactors on the measurement procedure is not well understood. This includes the location of the accelerometers within the head-form and testing the head-form under the variety of conditions necessary to establish its global performance. To address this problem, a simple model of the IHRA head-form has been developed. This model was created using MADYMO© and consists of a solid sphere with a second sphere representing the vinyl covering. Stiffness and damping characteristics of the vinyl covering were determined analytically from drop test data of an IHRA head-form.

The intent of this research is to understand the effects worn dampers have on vehicle stability and safety through dynamic model simulation. Dampers, an integral component of a vehicle's suspension system, play an important role in isolating road disturbances from the driver by controlling the motions of the sprung and unsprung masses. This paper will show that a decrease in damping leads to excessive body motions and a potentially unstable vehicle. The concept of poor damping affecting vehicle stability is well established through linear models. The next step is to extend this concept for non-linear models. This is accomplished through creating a vehicle simulation model and executing several driving maneuvers with various damper characteristics. The damper models used in this study are based on splines representing peak force versus velocity relationships.

One of the principal tools used by the accident reconstructionist to determine whether a vehicle occupant was properly restrained when an accident occurred is the examination and analysis of impact evidence and damage to interior structures of the vehicle. Careful analysis of such evidence not only assists in the determination of restraint usage, but can also provide insight into the pre-impact position of the occupant. However, the multi-faceted restraint systems and advanced materials used in modern vehicles can make the interpretation of vehicle interior damage difficult. This is especially true for impacts of mild or moderate severity, when interior damage may or may not be expected to occur, and the lack of any identifiable damage can be misinterpreted. In this paper, the restraint system damage resulting from a series of sled tests conducted at a range of mild to moderate impact severities with a normally positioned driver under various restraint conditions is discussed.

Kinetic Pty Ltd and Tenneco Automotive have developed a passive suspension system hereafter referred to as a Kinetic2 system. The motivation for the design of the system is discussed, and the function of the system is briefly explained. In a previous paper, the system has been shown to improve the stability and rollover resistance of a small SUV. In this study vehicle response characteristics are found by simulating a typical sinusoidal sweep maneuver. Improved handling is evaluated by simulating NHTSA’s yaw acceleration feedback fishhook test. Lastly ride is studied by simulating the vehicle driving over a characteristic stretch of California Freeway #5. All of the simulations were performed on a small SUV in standard form and equipped with the Kinetic system. Results of the ADAMS simulation are presented, and benefits are discussed.

An existing tire model was investigated for additional normal load-dependent characteristics to improve the large truck simulations developed by the National Highway Traffic Safety Administration (NHTSA) for the National Advanced Driving Simulator (NADS). Of the existing tire model coefficients, plysteer, lateral friction decay, aligning torque stiffness and normalized longitudinal stiffness were investigated. The findings of the investigation led to improvements in the tire model. The improved model was then applied to TruckSim to compare with the TruckSim table lookup tire model and test data. Additionally, speed-dependent properties for the NADS tire model were investigated (using data from a light truck tire).

The International Harmonization Research Activities Pedestrian Safety Working Group (IHRA PSWG) has proposed design requirements for two head-forms for vehicle hood (bonnet) impact testing. This paper discusses the development of MADYMO models representing the IHRA adult and child head-forms, validation of the models against laboratory drop tests, and assessment of the effect of IHRA geometric and mass constraints on the model response by conducting a parameter sensitivity analysis. The models consist of a multibody rigid sphere covered with a finite element modeled vinyl skin. The most important part in developing the MADYMO head-form models was to experimentally determine the material properties of the energy-absorbing portion of the head-form (vinyl skin) and incorporate these properties into MADYMO using a suitable material model. Three material models (linear isotropic, viscoelastic, hyperelastic) were examined.

This paper presents the results of a design space exploration based on the simulations of the MTV (Medium Tactical Vehicle) 5.0 Ton Cargo Truck using MSC-ADAMS (Automatic Dynamic Analysis of Mechanical System). Design space study is conducted using ADAMS/Car and ADAMS/Insight to consider parametric design changes in suspension and the tires of the cargo truck. The methodology uses an industry acknowledged multibody dynamics simulation software (ADAMS) for the modeling of the cargo truck and a flexible optimization architecture to explore the design space. This research is a part of the work done for the U.S. Army TACOM (Tank Automotive and Armaments Command) at the Center for Automotive Research, The Ohio State University.

The severity of an impact in terms of the acceleration in the occupant compartment is dependent not only on the change in vehicle velocity, but also the time for the change in velocity to occur. These depend on the geometry and stiffness of both the striking vehicle and struck object. In narrow-object frontal impacts, impact location can affect the shape and duration of the acceleration pulse that reaches the occupant compartment. In this paper, the frontal impact response of a full-sized pickup to 10 mile per hour and 20 mile per hour pole impacts at the centerline and at a location nearer the frame rails is compared using the acceleration pulse shape, the average acceleration in the occupant compartment, and the residual crush. A bilinear curve relating impact speed to residual crush is developed.

Kinetic Pty Ltd and Tenneco Automotive have developed a passive suspension system called a Kinetic system. The motivation for the design of the system is discussed, and the function of the system is explained. The system improves handling, stability, and ride by passively decoupling roll stiffness from articulation stiffness and roll damping from bounce damping. Improved stability is evaluated by conducting NHTSA's Roll Rate Feedback Fishhook tests on a small SUV equipped with the Kinetic system. Results of the testing are presented, and benefits to rollover are discussed.

This paper describes an adaptive control strategy for improving the steering response of an automated vehicle steering controller. In order to achieve repeatable dynamic test results, precise steering inputs are necessary. This strategy provides the controller tuning parameters optimized for a particular vehicle's steering system. Having the capability to adaptively tune the steering controller for any vehicle installation provides an easy method for obtaining precise steering inputs for a wide range of vehicles, from small off-road utility vehicles to passenger vehicles to heavy trucks. The S.E.A. Ltd. Automated Steering Controller (ASC) is used exclusively in conducting this research. By recording the torque input to the steering system by the steering controller and the resulting steering angle during only a single test, the ASC is able to characterize the steering system of the test vehicle and create a computer model with appropriate parameters.

This paper describes the design and development of the hardware, electronics, and software components of a state-of-the-art automated steering controller, the SEA, Ltd. ASC. The function of the ASC is to input to a vehicle virtually any steering profile with both high accuracy and repeatability. The ASC is designed to input profiles having steering rates and timing that are in excess of the limits of a human driver. The ASC software allows the user to specify steering profiles and select controller settings, including motor controller gains, through user-interface windows. This makes it possible for the test driver to change steering profiles and settings immediately after running any test maneuver. The motor controller used in the ASC offers self-contained signal input, output, and data storage capabilities. Thus, the ASC can operate as a standalone steering machine or it can be incorporated into typical existing, on-vehicle data acquisition systems.

This paper discusses the improvement of a heavy truck anti-lock brake system (ABS) model currently used by the National Highway Traffic Safety Administration (NHTSA) in conjunction with multibody vehicle dynamics software. Accurate modeling of this complex system is paramount in predicting real-world dynamics, and significant improvements in model accuracy are now possible due to recent access to ABS system data during on-track experimental testing. This paper focuses on improving an existing ABS model to accurately simulate braking under limit braking maneuvers on high and low-coefficient surfaces. To accomplish this, an ABS controller model with slip ratio and wheel acceleration thresholds was developed to handle these scenarios. The model was verified through testing of a Class VIII 6×4 straight truck. The Simulink brake system and ABS model both run simultaneously with TruckSim, with the initialization and results being acquired through Matlab.

In the field of accident reconstruction, there has been a significant amount of effort devoted to the calculation and derivation of vehicle crush energy and vehicle stiffness. Crush energy is usually calculated with a crush profile and crush stiffness. But, oftentimes, crush profiles and/or crush stiffnesses are not available and accident constructionists face the situation of insufficient information. In some such cases, the force balance method can be used to reduce the uncertainty. The method follows from Newton's Third Law, i.e., the impact force exerted on one vehicle is balanced by the force exerted on the other vehicle. With the help of this method, crush profile or crush stiffness can be derived. As a result, the crush energy can then be calculated with improved accuracy. This ultimately increases the accuracy of the overall accident reconstruction. In this paper, examples will be given to illustrate the use of such a methodology.

Delta-V and Barrier Equivalent Velocity (BEV) are terms that have been used for many years to describe aspects of what happened to a vehicle when an impact occurred. That is, they are used to describe some physical change in the vehicle state before the impact as compared to after the impact. Specifically, the Delta-V describes the change in the vehicle velocity vector from just before the impact until just after the impact. The BEV attempts to quantify the energy required to cause the damage associated with an impact. In order to understand what happens to a vehicle and its occupants during an impact, it is necessary to examine the acceleration pulse undergone by the vehicle during the impact. The acceleration pulse describes, in detail, how the Delta-V occurs as a function of time, and is related with the deformation of the vehicle as well as the object contacted by the vehicle during an impact.

The shape of an acceleration pulse in an impact is not only affected by the change in velocity, but also by the geometry and stiffness of the both the striking vehicle and the struck object. In this paper, the frontal crash performance of a full-size pickup is studied through a series of impact tests with a rigid pole and with a flat barrier. Each rigid pole test is conducted at one of four locations across the front of the vehicle and at impact speeds of 10 mph, 20 mph, or 30 mph. The flat barrier tests are conducted at 10 mph, 15 mph, 20 mph, and 30 mph. The vehicle crush and acceleration pulses resulting from the pole tests are compared to those resulting from the barrier tests. The severity of pole impacts and the severity of flat barrier impacts are compared based on peak accelerations and pulse durations of the occupant compartment.

This study investigated the jackknife stability of Class VIII double tractor-trailer combination vehicles that had mixed braking configurations between the tractor and trailers and dolly (e.g. ECBS disc brakes on the tractor and pneumatic drum brakes on the trailers and dolly). Brake-in-turn maneuvers were performed with varying vehicle loads and surface conditions. Conditions with ABS ON for the entire vehicle (and select-high control algorithm on the trailers and dolly) found that instabilities (i.e. lane excursions and/or jackknifes) were exhibited under conditions when the surface friction coefficient was 0.3. It was demonstrated that these instabilities could be avoided while utilizing a select-low control algorithm on the trailers and dolly. Simulation results with the ABS OFF for the tractor showed that a tractor equipped with disc brakes had greater jackknife stability.

During Phase VI of the National Highway Traffic Safety Administration's (NHTSA) Light Vehicle Rollover Research Program, three of the twenty-six light vehicles tested exhibited significant response asymmetries with respect to left versus right steer maneuvers. This paper investigates possible vehicle asymmetric characteristics and unintended inputs that may cause vehicle asymmetric response. An analysis of the field test data, results from suspension and steering parameter measurements, and a summary of a computer simulation study are also given.